favorite
favorite
hide
unhide
flag

Posted

print

Kohler K-series cast iron single cylinder engine parts (Sherman)

Kohler K-series cast iron single cylinder engine parts 1 thumbnailKohler K-series cast iron single cylinder engine parts 2 thumbnailKohler K-series cast iron single cylinder engine parts 3 thumbnailKohler K-series cast iron single cylinder engine parts 4 thumbnailKohler K-series cast iron single cylinder engine parts 5 thumbnailKohler K-series cast iron single cylinder engine parts 6 thumbnailKohler K-series cast iron single cylinder engine parts 7 thumbnailKohler K-series cast iron single cylinder engine parts 8 thumbnailKohler K-series cast iron single cylinder engine parts 9 thumbnailKohler K-series cast iron single cylinder engine parts 10 thumbnailKohler K-series cast iron single cylinder engine parts 11 thumbnailKohler K-series cast iron single cylinder engine parts 12 thumbnailKohler K-series cast iron single cylinder engine parts 13 thumbnailKohler K-series cast iron single cylinder engine parts 14 thumbnailKohler K-series cast iron single cylinder engine parts 15 thumbnailKohler K-series cast iron single cylinder engine parts 16 thumbnailKohler K-series cast iron single cylinder engine parts 17 thumbnailKohler K-series cast iron single cylinder engine parts 18 thumbnailKohler K-series cast iron single cylinder engine parts 19 thumbnailKohler K-series cast iron single cylinder engine parts 20 thumbnailKohler K-series cast iron single cylinder engine parts 21 thumbnailKohler K-series cast iron single cylinder engine parts 22 thumbnail
condition: good
make / manufacturer: Kohler
model name / number: K241, K301, K321

more ads by this user

I have several good used parts available for Kohler K-series (K241, K301, and K321) cast iron block single cylinder engines. I think most of these were originally from model 220, 222, 224, or 444 Case / Ingersoll garden tractors but will likely fit many other makes & models such as early Cub Cadets.

Engine Blocks ... I have 3 blocks available. One of each size (K241, K301, and K321). I don't have a real accurate bore gauge, but from what I could measure, the K241 block appears to have minimal cylinder wear (a couple thousandths or so) and may still work with a standard size piston after some light honing to clean up the bore (they all have some light surface rust from sitting). The K301 block has a bit more wear (around 9 or 10 thousandths at the worst spot) so it will likely need to be bored for a 0.020" oversize piston. The K321 block seems to have already been bored 0.030" over and has 5 thousands or so of wear over that. I don't know if this one will clean up at 0.040" over or if it will need a sleeve. Some of these blocks have some bolts broken off in the holes next to the exhaust port ... $50 each for the K241 and K301 blocks, $40 for the K321 block.

Crankshafts ... I also have 3 crankshafts available. They all have short 1" diameter output shafts for use with Lovejoy couplers in Case / Ingersoll garden tractors. Two of these crankshafts are out of K301 engines and I belive they will also fit K321's as well (same 3.250" stroke). The rod journals on these K301 cranks are standard size but have some wear and will need to be ground 0.010" or possibly 0.020" undersize. One of them also has a broken flywheel retainer "stud" that will need to be drilled & tapped for a bolt. The third crankshaft is out of a K241 and has had the rod journal ground 0.020" under so it is ready for use with a new 20 under connecting rod ... $55 each for the two with intact flywheel retainer "studs". $45 for the one with the broken "stud".

Flywheels ... I have 2 of these available (one of the 3 pictured has been sold). One has "236288" casting number. The other is # "47 300 01". Both are in good condition including the magnets and ring gears ... $60 each.

Camshafts ... I have 4 camshafts available. Two of them are in good condition and were marked according to the engine size they were removed from (one from a K241 and one from a K301). Although from what I understand, they're the same cam. The other two are in okay condition and were not marked. All include the lifters (tappets) and center pin ... $25 each for the good ones. $20 each for the okay ones.

Cam covers & dipsticks ... I also have 5 cam covers and 3 dipsticks available. Three of the cam covers are the style without the dipstick and two are the style with the dipstick. One of the ones with the dipstick is a little loose where the tube goes into the cover (might need to be crimped a little and/or some sealer added to the joint) ... $15 each for the covers with the dipstick, $5 each for the covers without a dipstick, and $10 for the dipstick that goes into the block.

Valves, Springs, and Retainers ... There are 5 valves and several springs, retainers, and keepers in this group of parts ... $20.

Valve cover breathers ... I have enough of these parts to put together 3 complete assemblies (minus one filter), 2 semi-complete assemblies (minus filters & stud), as well as a spare reed valve & cover ... $10 each for a complete assembly, $8 each for a semi-complete assembly (minus filter & stud), and $5 for the spare reed valve & cover.

Bearing plates ... I have 5 of these available. Two of them have the casting number "45 156 02". Two of them have the casting number "235815". And the fifth one (casting number "45 156 01") has a chunk broken off the edge. The broken out piece will be included for someone that can weld it back in place ... $15 each for the good ones, $5 for the one with the broken chunk.

Governor parts ... I have 6 governor gear assemblies, 5 shafts & bushings, 6 levers, 6 springs, and 5 stop pins available. Note that one of the levers has a small offset bend in it where the others are straight. Most of the levers are in good condition but a couple of them have noticeable wear in the hole for the throttle rod. Some bushings are worn more than others. Earliest buyers will get the best ones ... $20 each for a gear, shaft, bushing, lever, spring, and stop pin. $5 for a single gear, lever, or spring.

Throttle & choke brackets ... I have 5 throttle cable brackets, 3 choke cable brackets, and 6 speed control levers. Only a couple of the brackets still have the cable retainer clips on them. $3 each for a single bracket or lever. $8 for one throttle bracket, one choke bracket, and one lever.

Carburetors ... I have 4 used carburetors available. None of them appear to have any serious corrosion issues, but they do have some wear around the throttle shafts and other issues. Selling these as-is for parts or repair. Numbers on these carburetors are:
  • 4705315 SOLD
  • 47-053-04 ... had two of these, one SOLD, one still available.
  • 236636 ... also have two of these.
  • A237771 SOLD
  • A237772 SOLD
  • Walbro WHG 80 2284
$15 each for the carburetors.

Carburetor parts ... Also have some extra floats (a couple of them look relatively new) and some other miscellaneous new & used carburetor parts ... both newer looking floats have been SOLD, $5 each for the older looking floats, and $15 for all the other miscellaneous carb parts.

Points covers & pushrods ... I have 4 points covers and 5 push rods available ... $10 each cover, and $5 each rod.

Oil drain pipes ... Two oil drain pipes with plug. These were originally off Case/Ingersoll garden tractors with Kohler engines but might also fit other applications ... $8 each.

Oil pans ... I have 3 of these used oil pans available. These were originally off Case/Ingersoll garden tractors but might also fit other applications. One of them has the numbers "47 200 0" cast inside. The other two have the numbers "47 200 02" cast inside. One of them has a broken mounting bolt in one of the holes ... $20 each.

Cylinder heads ... Two used cylinder heads. One has the spark plug hole centered between the valves. The other has the plug hole over the exhaust valve ... $40 each.

Air cleaner housings ... One complete assembly (pictured at bottom of photo) available and two bases (at top of photo). The complete assembly has a good base but there a few dents in the lid. The larger of the two bases (pictured upper left) has some damage (cracks & missing pieces) around the mounting holes. The smaller of the two bases looks to be in fair condition but does have a bent tab ... $25 for the complete assembly, $10 each for the bases.

Flywheel shrouds ... Three flywheel shrouds and some other shields. Decals on the flywheel shrouds indicate that the two with provisions for a gear drive starter were off a K241 and K321. The other one (used with a starter/generator) was off a K301. Some of the top shroud pieces (that go over the cylinder head) have some bends & cracks in them ... $25 each flywheel shroud, and $5 each for the other shields pictured.

Stators ... Two charging system stators. Both appear to be in good useable condition. I tested them with an ohmmeter to make sure the coil windings are not burned out or short circuited to ground ... $15 each.

Starter / generator pulleys & flywheel screens ... These are the pulleys that attach to the flywheel on engines used with starter / generators. One of them (upper left in picture) is a stamped steel construction that measures 8" OD at the pulley and has the mounting holes spaced 5-⅞" apart. This one includes the 4 screws that attach it to the flywheel. The other pulley (pictured upper right) is cast aluminum, measures 8-¼" OD, and has the mounting holes spaced 6-¼" apart. I also have 3 flywheel debris screens. I believe these were originally off Case garden tractors with starter/generators. They are flat (not dished) and measure 7-½" diameter.... Pulleys SOLD, screens $15 each.

Starter ... This is an American Bosch starter that is stamped: "0599521M030SM". It has been bench tested and is in working condition ... $25.

All parts are available for local pickup in Sherman. Or, I can accept PayPal or money order and mail any of these parts to a buyer willing to cover the shipping (the blocks might be rather expensive to ship though).

I also have several new parts available for these Kohler K-series single cylinder engines ... please see my other ad.

post id: 7756507685

posted:

updated:

best of [?]

loading
reading
writing
saving
searching